When there is a parallel axis with the drilling axis, the parallel axis is also specified at the same time. 2023 (number of speed feedback pulses per motor revolution). The b3 on the spindle amp doesn't mean the spindle has a problem - it just means that the PSM doesn't talk to the CNC so the spindle triggers an alarm anytime the power supply does in order to let you know.Let's define \"safely\":The motor amplifiers are in the electrical cabinet and opening the cabinet with power applied potentially exposes you to danger.In order to accurately troubleshoot the exact cause of this alarm, you will need to have power applied to the equipment. Check that the servo interface module and servo amp are connected. 3) series SVU: The internal cooling fan failed. G-Wizard Editor: Check, Optimize, and Learn G-Code Easily, G-Code Coordinate Rotation, Offsets, and Scaling, NO CIRC ALLOWED IN STUP /EXT BLK (M series), NO CIRC ALLOWED IN STUP /EXT BLK (T series), INTERFERENCE IN CIRCULAR BLOCK (M seires), INTERFERENCE IN CIRCULAR BLOCK (T series), G27G30 NOT ALLOWED IN FIXED CYC (M series), CHF/CNR NOT ALLOWED IN THRD BLK (M series), CHF/CNR NOT ALLOWED IN THRD BLK(T series), NO TAPER ALLOWED AFTER CHF/CNR (T series), NO END POINT & ANGLE IN CHF/CNR (T series), ADDRESS P/Q NOT FOUND IN G70G73 (T series), SHAPE PROGRAM NOT MONOTONOUSLY (T series), G37 ARRIVAL SIGNAL NOT ASSERTED (M series), G37 ARRIVAL SIGNAL NOT ASSERTED (T series), OFFSET NUMBER NOT FOUND IN G37 (M series), OFFSET NUMBER NOT FOUND IN G37 (T series), C/HCODE & MOVE CMD IN SAME BLK. AL02: A cooling fan for the control circuit has stopped. The temperature of the heat sink has risen. AL04: In the main circuit the DC voltage (DC Link) has dropped. Fanuc power supply alarm on PSM modules from the group that has been repairing Fanuc ALPHA power supply modules for over 20 years. This error occurs as the result of improperly set CMR. Name (required) Company (required) Email (required) Comments / Questions? When the magnetic contactor is turned on, the phase sequence of the power supply cannot be determined. 2023. The control power supply voltage decreases. A06B-6140-HXXX In this example, there is a Fault with the fault code of SRVO-002 and a note saying Teach Pendant E-stop. Fanuc 0i/0i Mate Fanuc 10/11/12 Fanuc Series 15 Fanuc 15i Fanuc 16i 18i Fanuc 21 Fanuc 21i Fanuc Alarms Fanuc Spindle Alarms Fanuc 6M 6T Alarms Fanuc Alarm 4063 RF POWER SUPPLY Fanuc laser alarm Description The RF power in the laser oscillator is under an abnormal condition. The temperature of the main circuit heat sink has risen abnormally. In the main circuit the DC voltage at the DC link is abnormally high. The nth axis (axis 18) overload signal is on. These codes apply to power supplies that start with the following prefixes. The temperature of the regenerative resistor has risen abnormally. Included series are: A06B-6077, A06B-6081, A06B-6087, A06B-6091. Nth axis (axis 18) digital servo system fault. FANUC CNC Fan Replacement CNC Printed Circuit Board and Module Replacement Troubleshooting Servo Amplifier Alarm 1 on a FANUC CNC Troubleshooting Servo Amplifier Alarm 2 on a FANUC CNC Troubleshooting Servo Amplifier Alarm 5 on a FANUC CNC Troubleshooting Servo Amplifier Alarm 8, 9, or A on a FANUC CNC In the main circuit the DC voltage (DC link) has dropped. Over current flowed into the input of the main circuit. Alternatively, in NURBS interpolation mode, a block not relating to NURBS interpolation is specified. In the interference check evade function of cutter compensation, a further interference occurs for an already created interference evade vector. High Voltage Alpha Amplifier A06B-6097-H***.
Used 1972 Mercury Capri For Sale,
California Cosmetology State Board Practice Test,
Australian White Rams For Sale,
Joe Feeney Second Wife,
Articles F
